How do devices behave when "Direct" is selected in scenes?

Actuators Sun protection

Switch actuators / Dimmer

Radiator actuator / Room thermostat

Manual command

from transmitters.

Excluding push commands

Conversion according to the command.
Always executed
except when wind is active
.

Conversion according to the command. Always executed. For up and down commands, the selected mode is decisive for the conversion.

Direct cannot be selected.
For use, a trigger must be created in each case with a scene in which the desired targets are stored.

Push commands

for example from the wall pushbutton

Conversion according to the logic of the actuator.

Open-Stop-Close-Stop...

Push commands should not be used when the blind mode is active.

Conversion according to the logic of the actuator.

On-Off-On...

Dimmer:

Dim-up-Stop-Dim-down

Direct cannot be selected.
For use, a trigger with a scene must be created in each case, in which the desired targets are stored.

Time command

Direct cannot be selected.
For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.
For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.
For use, a trigger must be created with a scene in which the desired targets are stored.

Dawn

Astro function or dawn from the environmental sensor via HomePilot

Drive up to 0%

Switch off / switch on depending on mode

Direct cannot be selected.
For use, a trigger with a scene must be created in each case, in which the desired targets are stored.

Evening twilight

Astro function or dusk from the environmental sensor via HomePilot

Shutdown to 100% or ventilation position

Switch off / switch on depending on mode

Configuration only external

Direct cannot be selected.
For use, a trigger with a scene must be created in each case, in which the desired targets are stored.

Sun

From external sensors such as environmental sensor, wireless sun sensor, Troll Comfort DuoFern

Sun start > Move down to sun position

Sun end > Open to 0%

Prerequisite > Sun position must be defined

Special feature:

If the shutter is already below the sun position when the sun starts, the sun position is not approached. If the shutter is operated manually in the active sun program, there is no opening to 0% at the end of the sun.

If the sun position is exceeded or undershot, the shutter is switched off.

Direct cannot be selected.
For use, a trigger with a scene must be created in each case, in which the desired targets are stored.

Wind

Factory set to 0% (direction of wind can be changed under automatic wind).

With the active wind program no automatic commands and also no manual commands are executed.

Direct cannot be selected. To use wind, a defined target must be entered in the scene. Command is forwarded as time.

Direct cannot be selected. To use wind, a defined target must be entered in the scene. Command is forwarded as time.

Rain

Factory set to 0% (driving direction rain can be changed under automatic rain).

In the active rain program, no automatic commands are executed, manual operation can be used, e.g. to extend an awning again for protection when it rains. At the end of the rain, the actuator remains at 0% and does not move back to the original position.

Move down to 100% (direction of travel rain DOWN)

Actuator moves to 100% when rain starts. If the actuator was at 0% at the start of the rain, it also moves back to 0% at the end of the rain; other positions are not taken into account. If the shutter was e.g. half closed, the shutter remains at 100% at the end of the rain.

Direct cannot be selected. For the use of rain, a defined target must be entered in the scene. Command is forwarded as time.

Direct cannot be selected.
For use, a trigger with a scene must be created in each case, in which the desired targets are stored.

Closing contact

open or closed

For example, window/door contact or radio transmitter UP as sensor.

Direct cannot be selected.
For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.
For use, a trigger must be created with a scene in which the desired targets are stored.

HSA DuoFern
When opening the contact is regulated to 4°
.

When closing, the last set value is used.

Room thermostat:

Direct cannot be selected.

Smoke

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Temperature

Cannot be selected directly.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Motion

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Smartphone

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.

Direct cannot be selected.

For use, a trigger must be created with a scene in which the desired targets are stored.